Power plant boiler news, features and articles on each aspect of the


  • Production capacity: 2.8-2.9MW
  • Work pressure: 1.0-1.25 MPA
  • Applicable fuel: Biomass molding granules, wood chip, corn cob, saw dust
  • Applicable industry: Heating, Hotels, Schools, Hospitals

Product introduction

  SZL series vertical dual drums chain grate water pipe steam and hot water boiler, adopts quick fitting and assembly structure. The 4-6t/h boiler is of quick fitting pipe structure, exit shop after completely assembled, the boiler of 6-35t/h is composed of 2 main components. The upper assembled components is the body heat accepting part, and the lower assembled component is of combustion equipment. The former part of the boiler body is arranged an water cooling wall, the upper part of it is connected to boiler cylinder, and its lower part is connected to collective chest, so as to form a combustion room and absorb the radiated heat from the furnace. Its rear part is arranged with dense convection pipes between upper and lower boiler cylinders. The high temperature smog after combustion shall stand for twice returning flushing transversely to the heat accepting surfaces, and shall be introduced to coal saver singly arranged, and flow into duster and exhausted from chimney in the end.

CNC manufacturing technology

  The key processing technologies such as steel plate blanking, circling, drilling of drum and pipe plate are all adopt advanced CNC processing to reduce the assembly stress and prolong the service life of the boiler.

  Steel pipe cutting, thread pipe pressing and convection pipe processing adopt advanced CNC process.

  Automatic production line.

Advanced welding process

  The welding of important parts like the vertical and circular seams of the boiler, the pipes, the inside of boiler and the flange are all adopted automated welding processes such as submerged arc welding or gas shielded welding to ensure the welding quality. All the vertical and circular seams will be done 100% radiographic inspection.

  Tube flange weld adopts robot welding.

  The chain grate panel, front and rear smoke chamber panel adopts CNC plasma cutting machine to cut orderly and beautifully.

Unique structural design

  According to different capacity, different numbers of independent wind bins are set from front to back of the grate.

  The user can reasonably distribute the air according to different combustion conditions to ensure that the fuel is fully burned.

  Intake air secondary, disturb fuel gas in the furnace, to ensure the fuel fired totally. The independent secondary draft fan make it easy to control and adjust the wind and wind pressure.

  The spreader feeds evenly to prevent tempering.

Low NOx emissions

  Graded air supply and special furnace arch structure make the NOx emissions down to 100mg/m³.

  We have taken numerical simulations on different biomasses, we find the thermal efficiency is more than 90%.

Model Rated thermal power(MW) Rated working pressure(MPa) Rated output water temperature(℃) Return water temperature(℃)
SZL2.8-0.7/95/70-M 2.8 0.7 95 70
SZL4.2-1.0/115/70-M 4.2 1 115 70
SZL5.6-1.0/115/70-M 5.6 1.0 115 70
SZL5.6-1.25/130/70-M 5.6 1.25 130 70
SZL7.0-1.0/115/70-M 7 1.0 115 70
SZL7.0-1.25/130/70-M 7 1.25 130 70
SZL14-1.0/115/70-M 14 1.0 115 70
SZL14-1.25/130/70-M 14 1.25 130 70
SZL21-1.0/115/70-M 21 1.0 115 70
SZL21-1.25/130/70-M 21 1.25 130 70
SZL29-1.0/115/70-M 29 1.0 115 70
SZL29-1.25/130/70-M 29 1.25




Cogeneration - WikipediaCogeneration or combined heat and power (CHP) is the use of a heat engine or power station Steam turbines for cogeneration are designed either for extraction of some steam at . The HRSG is designed based upon the specific features of the gas turbine or reciprocating engine that it will be coupled to. .. Article · Talk Power station - WikipediaA power station, also referred to as a power plant or powerhouse and sometimes generating In September 1882 in New York, the Pearl Street Station was established by Edison to The efficiency is not directly a function of the fuel used . For the same steam conditions, coal-, nuclear- and gas power plants all have the Supercritical and ultrasupercritical coal-fired power generation | Tan Print this article USC is routinely used for new pulverized coal power plants in Japan today. Coal-fired electricity generation versus coal consumption per kWh in China, . DEC manufactured the boilers, while turbines and generators were produced by HEC. Table 6. Comparison of SC/USC technology features, 2008 

Steam Generation Thermodynamics 101 - Power Engineering1 Nov 2008 It&39;s therefore worthwhile to address a few fundamentals of steam production. Q = Heat input per unit time: W S = Shaft work such as that done by a . Consider the common drum boiler, where steam leaving the drum is saturated. = 1 TL /TH. A recent article in Power Engineering (Latest Steam 

(PDF) Cost analysis of a coal-fired power plant using the NPV methodTotal direct plant cost involves the cost of equipment (i.e. boiler, steam turbine, This article is published with open access at Springerlink.com Fuel cost per tonne . mathematical optimization for the new design of power correlations were developed to estimate the cost of steam as a function of the raw material cost Thermal Power Plant Working | INDIAN POWER SECTORConsists of working of thermal power station in detail with each part defined and consists This is achieved by raising the steam in the boilers, expanding it through the .. Badarpur Thermal power plant, NTPC, Badarpur, New Delhi, NCT Delhi hand information or articles related to Power Sector then mail your details at Safety | Boiler inspection and maintenance | Plant Services3 Dec 2009 Boilers have a variety of safety features designed to prevent within the boiler if other systems fail, every steam and water-heating boiler must Pushing the steam cycle boundaries - Power Engineering International1 Apr 2012 In fact, coal fired plants using this cycle account for about 40 per cent of global other component, influences the overall power plant efficiency and the key features are: 740, which has just been approved by ASME for use in new steam plant boilers. . More Power Engineering International Issue Articles.